The Kenmore Elite washing machine is a premium cleaner. It is also among the largest front-loaders with an enormous capacity. The washer has top-notch features like a self-cleaning system and an infinite spin cycle. It is truly one of the en vogue machines in the market today. Water leakage can be a significant problem in any home. Not only will it cause a lot of damage to your floors, but it will also make the inside of your home damp and dirty.
A Kenmore elite washer leaking has many negative repercussions, such as mold, mildew, and damage to your washing machine. Check for any signs of leaking regularly and replace damaged parts immediately. A leaking washer indicates that something is wrong with the machine. If you notice a leak coming from the washer, inspect it and try to repair it as soon as possible. Here are some of the common reasons for leaks and how you can solve them
1. Cracked or Damaged Drain Pump
The drain pump is a small motor powered by electricity. It is located under the front of the machine. It works by sucking up water from the bottom of the machine as it fills up. This pump is prone to damage because it consists of electrical and moving parts exposed to a lot of wear. If the pump stops working, water will accumulate in the machine and eventually spill out of the bottom or sides of your washer.
Listen for any unusual sounds coming from the base of your washer when it is operating. This may mean some part of your drain pump has broken or worn out. A visual inspection can also give you an idea about the state of your pump. The bearings or gears of the motor may have rusted or corroded. You can figure out whether there is any water leakage by lifting the lid on your machine. A square plastic plate will cover the drain pump. If there is water collecting in this area, you should replace it immediately. Before replacing the pump, locate your appliance manual for instructions on detaching the pump and its electrical specs.
Relevant: Samsung Washer Quick Test Mode Drain Pump Test
2. Torn Tub Seal
The tub seal is the rubber seal located at the bottom of the machine. It prevents water from seeping into a small gap underneath the tub and drain pump. It is subject to wear and tear over time. It may also wear out if your washer performs a lot of spins. Tub bearings can also rust over time. The tub seal is a barrier between the outside and inside of your washer. If it is torn or cracked, water seeps through and leaks on the floor.
Check for any tears or cracks in the tub seal. You can do a visual check by lifting the front panel of your washer. Check for any mold or mildew on the seal. The edges of it may have worn down over time. Replace both the tub seal and the bearings if they show severe wear and tear. This process will require disassembling the machine. Consider hiring a professional to perform the task if it is beyond your skills.
3. Torn Door Boot Seal
The door boot seal is a rubber ring that goes around the entire front door of your washer. It helps to contain water in the machine and prevent leaks when the pump works. It also acts as a barrier between the tub and the door of your washing machine.
Check for any tears, cracks, or holes in the rubber seal around your washer door. A tear or hole may be all that is needed to allow water to leak on your floor. If there are any holes, you should replace the door boot seal. The rubber may be very tight. Use some force when detaching it. Kenworth washers feature an easy-access seal. Some machines may have a screw or several screws that hold the seal.
4. Damaged Tub-to-Pump Hose
This hose connects the drain pump and the bottom of your tub. It is a long plastic tube that goes down to the main body of your washer. The hose may be cracked or torn if you use your washer regularly. It will eventually wear out because of friction and pressure when the pump drains water. Water can easily seep through cracks or holes in the hose and leak on your floor.
Inspect the connections between the hose and the main body of your washer. Make sure that they are not corroded and completely sealed from water leakage. Any leaks can also go unnoticed at first. Replace the hose immediately if it has a hole or cracks in it. Remember to seal off the connection with a strong sealant or silicone.
5. Leaking Pump Drain Hose
The pump drain hose is part of your washer’s drain system. It is essentially a long tube that connects from your pump to the bottom of your machine. It allows water to flow from the pump into your machine’s tub. The hose also has a valve at the end of it. The valve regulates the pressure of water flowing into your tub as it fills up. It closes when the draining stops and prevents water from leaking back to your washer.
Related: LG Washer Leaking Water Into Drum: Reasons & Quick Fixes!
Check for any cracks in your drain hose by lifting the front panel of your machine. You should also check that it is properly connected to the pump. Check whether any threading between these two components is loose or missing. Also, check for any small holes or cracks in the tube. When replacing the hose, apply grease around the valves and threads to help seal them.
Kenworth washers are durable. They can offer a long service life if taken care of properly. The repairs involved in caring for your machine are not challenging. It is best to consult with an authorized technician when you’re unsure about how to work on your machine. A professional can help you ensure that your machine’s parts are functioning at their best and that they don’t become damaged. You should also follow the manufacturer’s guidelines for maintaining or repairing your appliance.