Even in this era, there is the possibility that you might find some glitches in your washer. One of them would be like the Maytag washer takes too long to wash. Due to the washer taking a long time can disrupt your day to day chores or routine.
So instead of sitting around, the first thing to do is find out why the washer is taking so long to wash. The problems you face can happen for many reasons, such as malfunction occurring in the load sense system, issues in the water inlet valve, etc. If you want to know more about the causes, stay hooked with us.
Reasons Why Maytag Washer Takes Too Long To Wash
Above, we have mentioned some glimpse of why your Maytag washer is taking a long time to wash. Now we will see the reasons in detail.
Load Sense System
The Load Sense system in the washer has been a blessing as it helps us understand how much weight the washer can take in each cycle and save from wasting water. But as much as it is a blessing, it can also be the reason for the delay of your washer taking long to wash.
Now how is that? It can happen if the weight you have placed in the washer has a mixture of both light and bulky items.
Due to this mixture, the washer readjusts its settings and cycle length, prolonging the washing time. Therefore make sure to put light and bulky items separately to avoid load sense system error.
Related: Maytag Bravos Washers Stuck on Sensing?
Water Inlet Valve
The job of the water inlet valve is to open so that the machine can fill to the precise level and then wait until the sensory detectors give the green signal that the correct amount of water has been supplied for the cycle to start and the washer to start washing.
While operating the washer, if you see that the washer is taking a long time to wash, you must check the time the water takes to fill in before starting the cycle. If it takes more time, there is some issue with your water inlet valve, by any chance. Get your water inlet valve cleaned or replaced immediately.
Drain Hose Installation
Sometimes we miss the reason for the problem because we don’t look into the little knacks of the problem.
Like in the washer case, we can consider checking the drain hose installation. It is a possibility that the drain hose of the washer is not properly installed because it cannot infiltrate the wastewater properly.
The lateness in the draining task also affects the timing for the washer to start its cycle, hence the delay in washing. To avoid such a problem, make sure that the opening of the drain hose is not tapped or that the inside of the hose is not clogged with dirt and debris.
Relevant: Washing Machine Drain Pipe Clogged
Water Pressure
The correct water pressure is very important for the washer. It is needed for the detergent to be removed from the drawer; if it is not removed properly, then the remaining detergent residue can block the washer’s inner systems.
So do check the fact that you are getting the correct pressure or not by looking into the pressure gauge attached to the washing machine or by attaching a pressure gauge to the valve behind the washer. After doing all this, if you see that you are receiving lower water pressure, get it fixed.
Selection Of Additional Function
Due to command of additional function apart from the usual washing such as extra rinse or prewash can prolong the wash timing longer.
FAQ
How long does a Maytag washer take to wash clothes?
It can take approximately 45 minutes to 1 hour to wash clothes in the washer using the normal wash cycle. But this is not the only fact that determines the time. The amount of water pressure you are receiving and the time the machine takes to fill also affects the washer’s timing to wash the clothes.
Does the Maytag washer have the feature of quick wash?
You need to go to a meeting, but all your clothes are dirty and washing them will takes tons of time. But if you are using the Maytag washer, then you saved. The reason is they have the quick wash feature in their washer.
This feature allows for washing faster by cutting down the wash while boosting the motion and temperature. Also, you can relax because your clothes will be clean as it is done in a normal wash cycle.
Conclusion
Hopefully, the reasons we have presented to you have helped you understand why the Maytag washer takes too long to wash.
Like the problem with the water inner valve, having an issue with sensory load system which can occur due to imbalanced weighted items placed in the washer, not having washing machine drainage hose properly worked or installed which can lead to not release of the wastewater of the cycle etc.
So it is important to look into these reasons to avoid the delay in washing. Lastly, it can happen that your washer might be facing more critical problems, so without hesitation, get the help of a professional for further diagnosis.