A malfunctioning washer can easily be a pain in your neck when you have a pile of clothes to wash. Your Maytag Centennial Washer won’t start due to power source issues, a defective lid switch, and a faulty lid lock system. Therefore, a faulty timer, an erratic motor, and a damaged control board are also responsible for not turning on your washer correctly.
You can wash your clothes with your water once you solve those problems. Fortunately, we compiled this Maytag washer troubleshooting guide to fix the issues that cause your washer to not start.
The best part is- we will also show you how to recalibrate your Maytag Centennial Washer at the end of this guide. So, keep reading between the lines.
Maytag Centennial Washer Won’t Start: 7 Easy Solutions
This chapter will disclose the culprits that prevent your washer from turning on. Plus, we also described what to do when Maytag Washer won’t start in the ‘Solution’ section.
01. Power Source Issue
Your Maytag washing machine won’t start if there is an issue with the power source or electric supply. You need to plug the washer into a grounded 3-prong outlet. Otherwise, your washing machine won’t get sufficient power to run. Above this, you may forget to plug your washer into the outlet (though it’s often overlooked). Either way, a tripped circuit breaker or a blown-out fuse can also be the reason to prevent your washer from turning on.
Solution:
Firstly, start with checking whether you plug your washer into a dedicated outlet or not. If not, plug the electric cord into a 3-prong outlet. Next, take a look at your circuit breaker. If it gets tripped, flip it to the On position. Lastly, inspect the fuse for a blowout. If required, replace it with a new one. If you are not electrically inclined, call a certified electrician for help.
02. Lid Switch Gets Bad
The switch inside the lid or lid switch is the main control of your washing machine. If it stops working, your washer won’t start. It doesn’t require elbow grease to determine whether the lid switch is at fault or not. Regarding this, you may need to open the top to access the switch. Turn the power on, depress the switch, and listen for a click. If you don’t hear the click, we bet the lid switch gets defective.
Solution:
Replacing the lid switch is an easy fix if it gets faulty. If you don’t know how to replace a lid switch on Maytag Washer, check out this tutorial.
However, sometimes the washer won’t start though the lid switch is working properly. In this case, inspect to see if your washing machine has a special fuse for the lid switch. If it gets blown out, just replace it with a new one. You might access the control panel to do this task.
Related: Kenmore Washer Lid Switch Bypass
03. Problem With Lid Lock
Some new washer models won’t work with the lid open. So, you should lock the lid before starting the washer. Some models have lights on the console, which will come on when the lid is locked. If the light comes on but the washer won’t start, this could be the problem with the lid lock. It will happen either the wiring down to the door lock gets loose or the door catch fails to activate the lock system.
Solution:
First off, inspect the wiring that runs to the door lock to see whether the wiring gets loose or burned. If it gets loose, tighten it up. Otherwise, you should repair the wiring. If the wires are in good shape, the lid lock system gets defective. In this case, you need to replace the lid lock assembly. Check out this tutorial to learn how to change the lid lock.
More lid lock problem solving relevant article you’ve been missing –
Maytag Washer Lid Lock Bypass: Tricks & Tips You Should Know!
Amana Washer Lid Lock Bypass: The Complete Guide
How to Bypass the Lid Lock on a Whirlpool Washer
04. Issue With Timer Knob
Maytag washer uses a mechanical timer knob. Your washer won’t run until the water in the machine has filled to the selected level. If the knob doesn’t line up properly with the graphics on the control panel, you can’t run your washing machine. Therefore, the timer will get faulty if one of its gears gets broken.
Solution:
Try to troubleshoot the washing machine problem by advancing the time a little bit. Once you have done this, pull the timer knob a little way and see if the washer will start properly. However, we want to mention that fixing a timer requires a lot of experience. So, it would be better if you hand over this task to a professional.
05. Motor Gets Defective
All washing machines including Maytag use a motor, which spins & agitates during the cleaning cycle. Most top-load washer brands use a reversing motor. It means the motor rotates in one direction for agitating and another for spinning & draining. If the motor doesn’t start but makes a buzzing noise, we bet the motor gets defective.
Solution:
Firstly, inspect the motor first to verify it’s at fault. To do this, pull out the drive or the pump belts and start the motor. On direct drive models, you should disconnect the pump and the direct drive coupling to the transmission. If the motor starts, the culprit is either the transmission or the pump. If the motor doesn’t start or makes a humming noise, you need to replace it. Watch this tutorial to learn how to change the motor on Maytag Washer.
06. Improper Water Supply
Your Maytag washer won’t run or wash if your washer is unable to fill appropriately. The following reasons are responsible for improper water supply:
- The hot water and cold water faucets are not on.
- Hoses are not attached to the inlet valve
- The inlet valve screen shave gets clogged
- Inlet hoses get kinked
Solution:
Start with inspecting both hot and cold water faucets. Make sure they are in the On position. Next, ensure the hoses are attached to the inlet valve. If not, attach them to the inlet valve. On the other hand, if the inlet valve screen-shave gets blocked, release the blockage. Finally, straight the inlet hoses if they get kinked.
07. Defective Control Board
A defective control board doesn’t provide sufficient power to the drive motor, fill valve, drain motor, or door lock. Consequently, you can’t operate your washer to wash your clothes. The wiring between the user interface and the control board is at fault or gets damaged. If the wiring gets cracked or loose, the control board doesn’t get any electrical signal. And it causes your washer to not start.
Solution:
The main control board on your washing machine is complicated and challenging to diagnose. We recommend you visually inspect the washer for a cracked or burned electrical wiring connection or damaged components. It will be better if you hire a certified technician to deal with this problem and replace the control board.
How To Reprogram Maytag Centennial Washer?
Follow the below steps to reset or recalibrate your Maytag Centennial Washer.
First off, plug your washer into the electrical outlet. Then, counter-clockwise the control knob all the way down for one time. Then, turn the control knob three times to the right.
Then, turn the control knob to the left for one. Afterward, rotate the control knob to the right again. Now, you can find the light starts blinking. It means the washer starts resetting or recalibrating its program. The light will keep blinking until it finishes the resetting program.
Once it’s done, your washer will turn off automatically. Now, turn on your washer and we bet you find it to work properly this time.
Related Maytag washer repair info:
Maytag Bravos XL Washer Won’t Turn On: 7 Troubleshooting Steps To Fix
Maytag Bravos Washers Stuck on Sensing?
Maytag Washer Makes a Loud Noise When Spinning
Conclusion
Maytag Centennial is a widely-accepted washing machine almost every homeowner uses to wash clothes. However, it starts malfunctioning over time just like other electric appliances. Maytag Centennial washer won’t start is one of the common washing machine problems. You can’t turn on your washer due to a power source issue, defective lid switch, and others.
And we described how to troubleshoot & solve these issues. So, follow our guidelines step by step to let your Maytag Washer function again.